VRRP配置『配置环境参数』SwitchA通过E0/24与SwitchC相连，通过E0/23上行SwitchB通过E0/24与SwitchC相连，通过E0/23上行交换机SwitchA通过ethernet0/24与SwitchB的ethernet0/24连接到SwitchCSwitchA和SwitchB上分别创建两个虚接口，interfacevlan10和interface20做为三层接口，其中interfacevlan10分别包括ethernet0/24端口，interface20包括ethernet0/23端口，做为出口。『组网需求』SwitchA和SwitchB之间做VRRP，interfacevlan10做为虚拟网关接口，SwitchA为主设备，允许抢占，SwitchB为从设备，PC1主机的网关设置为VRRP虚拟网关地址192.168.100.1，进行冗余备份。访问远端主机PC210.1.1.1/24

(VRRP configuration "Configuration Environment Parameters" SwitchA is connected to SwitchC through E0/24, SwitchB is connected to SwitchC through E0/23, and SwitchA is connected to SwitchC through E0/23 and SwitchA is connected to SwitchA through ethernet0/24 and ethernet0/24 of SwitchB. Create two virtual interfaces on SwitchB and interfacevlan10 and interface20 as Layer 3 interfaces. Interfacevlan10 includes ethernet0/24 ports respectively, and interface20 includes ethernet0/23 ports as egress. "Networking requirements" VRRP is used between SwitchA and SwitchB, interfacevlan10 is used as the virtual gateway interface, SwitchA is the master device, allowing preemption, SwitchB is the slave device, and the gateway of the PC1 host is set to the VRRP virtual gateway address 192.168.100.1 for redundancy. backup. Access the remote host PC210.1.1.1/24)

[下载]11003814262.rar

2022-8-26 11:00 上传

文件大小: 60 KB
下载次数: 0

VRRP配置『配置环境参数』SwitchA通过E0/24与SwitchC相连，通过E0/23上行SwitchB通过E0/24与SwitchC相连，通过E0/23上行交换机SwitchA通过ethernet0/24与SwitchB的ethernet0/24连接到SwitchCSwitchA和SwitchB上分别创建两个虚接口，interfacevlan10和interface20做为三层接口，其中interfacevlan10分别包括ethernet0/24端口，interface20包括ethernet0/23端口，做为出口。『组网需求』SwitchA和SwitchB之间做VRRP，interfacevlan10做为虚拟网关接口，SwitchA为主设备，允许抢占，SwitchB为从设备，PC1主机的网关设置为VRRP虚拟网关地址192.168.100.1，进行冗余备份。访问远端主机PC210.1.1.1/24

(VRRP configuration "Configuration Environment Parameters" SwitchA is connected to SwitchC through E0/24, SwitchB is connected to SwitchC through E0/23, and SwitchA is connected to SwitchC through E0/23 and SwitchA is connected to SwitchA through ethernet0/24 and ethernet0/24 of SwitchB. Create two virtual interfaces on SwitchB and interfacevlan10 and interface20 as Layer 3 interfaces. Interfacevlan10 includes ethernet0/24 ports respectively, and interface20 includes ethernet0/23 ports as egress. "Networking requirements" VRRP is used between SwitchA and SwitchB, interfacevlan10 is used as the virtual gateway interface, SwitchA is the master device, allowing preemption, SwitchB is the slave device, and the gateway of the PC1 host is set to the VRRP virtual gateway address 192.168.100.1 for redundancy. backup. Access the remote host PC210.1.1.1/24)

[下载]11003814262.rar

2022-8-26 11:00 上传

文件大小: 60 KB
下载次数: 0