(With the full-automatic PXE network engraving tool of Chenglong network, you do not need to set up DHCP and TFTP servers, nor do you need to set up the ghsot server. It is truly full-automatic network engraving. You only need to start the client settings from the network card. NF series network cards are supported. It supports overall network engraving and single partition network engraving. Network managers can easily network engraving. They no longer need to set the type of network engraving on each client. They can easily network engraving by clicking the mouse on the server. In order to make the network engraving faster, we automatically separate the IP segment from the normal network segment. After the network engraving is completed, just click restore IP to restore the original IP settings. When switching between different types, turn off the tftpd first, and recover the IP first. Otherwise, the IP recovery will definitely fail, and the PXE in the tftpd will not change Cause wrong division Ghost11.0.1.1533 is newly added, and the problem that IP cannot be restored after changing the type of screen engraving is corrected. I hope that you will not reply to boring posts when replying, and give us more valuable comments. Due to space constraints, we will decide whether to delete the 8.3 version of the tool according to the feedback of netizens after the release of version 11.0. Precautions for using the Chenglong NetView PXE netlock tool: 1 The Chenglong Netcom PXE netlock tool has its own DHCP service function. There can no longer be a second DHCP server in the same LAN. Otherwise, the boot image cannot be correctly assigned to the IP or cannot be obtained through TFTP after being assigned to the IP. In case of any of the above situations, check whether the DHCP service is enabled on the route and server. If the DHCP service is enabled by default on some low-end hard routes, please turn off DHCP or disconnect the network cable connected to the route. 2. single partition Netflix: some friends say that the C disk is OK, but the D, e and f disks will report errors. Let me explain here. The single gram D disk here means that if you have more than two partitions in your image, you can only block the second partition. If you have only one partition in your image, selecting a single gram D disk will report an error. In practice, sometimes you only need one partition, but you don't want to do a full disk image. Here's a solution. For example, Internet cafes only want the e disk of the single gram game partition. At this time, you can mirror the e disk. When you select the e disk of the single gram, the ghost server will report an error saying that the requested partition is invalid, regardless of whether it removes the prompt. Then click stop, and then select the partition you want to block in the partition. 3. The ghost server is recommended to use the 2003 operating system and turn off the firewall and anti-virus software, followed by 2000 and XP. If the NF series motherboard is used, it is a good choice to insert a 8139 network card separately. 4. do not network machines with different types of network cards at the same time, which will seriously slow down the speed. If there are 100m switches and Gigabit switches in the network at the same time, it is better to separate the network 5 If it is a SATA hard disk, the interfaces of some garbage motherboards will also seriously affect the netgram speed. If the speed of interface 1 is only 60m/ min, the speed of interface 3 will soon reach 700/ min. it is strange but it is really a problem. 6. the client can connect to the server and start ghost11. After clicking send data, the client does not respond and does not transmit data. What's the matter? Sometimes this happens. You can stop sending and manually change the default multicast to broadcast. Once, the client didn't make progress after sending it. It was manually modified to broadcast, and the speed was very fast. In 100m environment, the initial speed is 1200m/ min. later, more than 800 m/ min clients are set to start from the network card. Note: set in BIOS. The specific settings vary slightly according to the BIOS type Find the value that firstbootdrivce can set in your BIOS: floppy means boot with floppy a:; Ls-120 indicates that the machine is powered on with ls-120 high-capacity floppy drive; Hdd-0 indicates that the primarymaster's ied hard disk is powered on; SCSI means boot with SCSI device; CDROM means boot with the optical drive on the IDE interface; HDD-1 indicates that the IDE hard disk of primaryslave is powered on; Hdd-2 means boot with IDE hard disk of secondarymaster; Hdd-3 means boot with IDE hard disk of secondaryslave; Zip100 means boot with zip high-capacity floppy drive; LAN means remote startup from the remote host of LAN; Disabled indicates that no boot device is specified. Find onboardlanbootrom in integratedperipherals? Change to enabled. This site provides Chenglong network's full-automatic PXE screen engraving tool. The copyright belongs to the source author or the company.
This document contains the following attachments:
PXE_ ghost11.0. exe....)
收藏
